How Do I?

Re: Trouble finishing bracelets and necklaces with crimps

AmysHandMadeSilverJewelry.com — Thu, 07 Feb 2013 18:52:15 GMT

I'm glad I could help, and tickled with the positive feedback as that was my first forum post.

Re: Trouble finishing bracelets and necklaces with crimps

tcwhit — Thu, 07 Feb 2013 12:22:10 GMT

Since I'm a total train wreck when trying to finish a piece off, this is a post I'm keeping as a favorite.

Re: Trouble finishing bracelets and necklaces with crimps

IVedros — Thu, 07 Feb 2013 05:29:56 GMT

Amy,

Thank you so much for the idea with the board. I put one together and it worked like a charm.

Ida

Re: Trouble finishing bracelets and necklaces with crimps

IVedros — Sat, 26 Jan 2013 18:09:15 GMT

Great idea Sue! This looks like it will really help. It reminds me of the "boats" my youngest brother used to make to pull along in the ditch. : )

Re: Trouble finishing bracelets and necklaces with crimps

SCB1 — Thu, 24 Jan 2013 00:29:00 GMT

Amy,

Very nicely illustrated and explained. Thanks for your input.

Re: Trouble finishing bracelets and necklaces with crimps

AmysHandMadeSilverJewelry.com — Wed, 23 Jan 2013 21:16:03 GMT

You have the final bead on, then crimp bead and the jumpring on the finding (clasp.)

Take your Beadalon back thru the last bead (3 if you can.)
The large loop you should still have can be hooked onto a nail, needle or pin. (see picture) With your needle nose pliers, pull your Beadalon as tight as possible back thru the beads.
Having your Beadalon hooked onto the nail allows you you maneuver your Beadalon and beads until they are maximum tightness where as it can be quite taxing on the hands otherwise.
When you have wiggled your beads as tight as you can get them,(still holding the Beadalon tight with your needle nose) crimp your crimp bead before they have a chance to wiggle loose.
With the beads bent slightly for best access to your extra stringing material, and holding the Beadalon, use your flush cutting snippers and cut the Beadalon. I find it is best to cut at a steep angle and I can usually tuck the little tail into the fourth bead and it can't be seen.

photo from The Basics of Bead Stringing

Amy at www.AmysHandmadeSilverJewelry.com

Re: Trouble finishing bracelets and necklaces with crimps

AlexiaFF — Sun, 20 Jan 2013 04:11:25 GMT

Hi Ida,

For the other end of bracelet or necklace: place crimp bead on after last bead placed, then finding (lobster clasp or soldered ring) go back through crimp bead and down through two beads. Pull the wire, slide the crimp bead down, pull wire, slide crimp bead down. Repeat this until you have a small space between your crimp bead and the finding. Then smash crimp bead. Cut wire tail off. As you are pulling on the tail of wire you are tightening up the beads that are strung.

Re: Trouble finishing bracelets and necklaces with crimps

shanks — Sun, 20 Jan 2013 03:18:31 GMT

Welcome Ida,

You might try using about a size 10 needle to assist you. When you are sending the stringing wire back down through the finding and the crimp, put a needle in the loop. Pull the bead up as close to the finding as you can and with the needle inserted in the loop pull down on the wire going through the crimp. This gives the beading wire something to slide over other than the finding, when fairly tight pull the needle out. sometimes you can get the last little slack out with a tug on the beading wire. Hope this is clear enough. You might practice a little before doing something as a finished product.

Trouble finishing bracelets and necklaces with crimps

IVedros — Sun, 20 Jan 2013 00:51:50 GMT

I made 2 bracelets today and had the hardest time finshing off the last end. I am using Beadalon wire and crimps. I can not seem to get the second end finished without having a large loop or extra space between the strung beads. Any tips would be greatly appreciated as this is driving me nuts!

Ida